#Dosbox output how to#
#Dosbox output install#
#Dosbox output software#
#Dosbox output code#
#Dosbox output download#

Because they can overlap, different looking segment + offset combinations can point to the same physical address. Hexadecimal:ĭifferent segments can overlap and even point to exact same region. You get the physical addresses from a segment and pointer by multiply the segment with 16 and then adding the pointer value to it.įor example if DS is 0x2052 and SI is 0x05BC, the physical address will be 0x20ADC. Together with a register in the second column they can point to a specific address in the memory. FS and GS can be referred to as Far segment and Global segment respectively, but there is no difference between them. Their value is an address in the physical memory divided by 16. Each define a 64 Kb large region of memory space. Meaning that if EAX is set to 0xFFDD9900, AX is 0x9900, AH is 0x99 and AL is 0x00.Īfter the two columns we find a bunch of Segment registers. EAX will access all 4 bytes (32-bits), AX will access the two lower bytes (16-bits), AH will access the higher byte of AX and AL will access the lower byte of AX. For example the bytes in the Accumulator can be referenced by EAX, AX, AH and AL.

#Dosbox output code#

The bytes in the GPs can be referenced in code by four different ways. In the first column we have the four general purpose registers (Accumulator, Base, Count and Data) and their current 32-bit value. In the above screen shot you can see that EIP was changed. Registers and flags that were changed by the previous executed instruction will be highlighted. Meaning that the most significant byte is shown first. The registers represent “memory slots” in the emulated CPU.Īll values shown are displayed in big endian fashion. It shows all the registers, flags and their current values (There is also some other stuff on the right side I haven’t 100% figured out yet). Register Overviewįirst section of the screen is the Register Overview. Almost all numbers are shown in hexadecimal. In the text below I assume you are familiar with bits, bytes and hexadecimal formatting. The commands are also listed on this page. When the execution is stopped, you can type “help” in the debug screen to see additional commands to use. Or if you want to start debugging immediately, start the application by typing “debug” before the name of the executable. You can start an application as normal and then press Alt+Break and F5 to stop/start the execution of code.

#Dosbox output download#

If you already have DOSBox installed, you’ll only need to download the EXE-file and add it to the folder where regular DOSBox is installed.ĭOSBox Debugger will start as the normal version of DOSBox, but with the additional debug screen showing.

#Dosbox output install#

How the get the Debug screenįirstly, to even see this screen in DOSBox, You’ll need to install a special debug version if it. So I have, in order to make myself understand it better and to make it easy for anyone else who want to follow my footsteps, decided to write this overview of the screen and its parts. And when being new to both, the debug screen in DOSBox is a bit overwhelming.

#Dosbox output how to#

Instead, I had to manually configure DOSBox-X to print to a file.I have recently begun the journey of learning to code old DOS assembly and how to debug it in the debug version of DOSBox. Configure DOSBox-X to write to a physical fileĪlthough the recommendation for most tutorials is to configure DOSBox-X to print to a physical printer, I was unable to get this working on Ubuntu 20.04. For Windows, MacOS or RPM users, DOXBox-X can be downloaded directly from the official dosbox-x site.

If you're not on Ubutunt, see if DOXBox-X can be installed through other means.

#Dosbox output software#

This can be launched with Ubuntu Software center. Installing DOSBox-X on Linux is as simple as installing the snap. Write a script which listens on the physical file.Configure DOSBox-X to write to a physical file.For assistance setting up a default raw printer in Linux see here Contents This tutorial assumes you already have a raw printer setup and set as the default printer. Using Ubuntu 20.04 and a fork of DOSBox called DOSBox-X, printing can be configured as follows.

Using DOSBox 0.7.4-3 I was unable to get printing working, so I'm using DOSBox-X instead.

Although DOSBox offers printing support, the documentation is sparse and most articles refer to printing on a Windows host.

Printing to a raw printer from DOSBox Summary